IC CD4013 PDF

The CD dual D flip-flop is a monolithic complementary MOS (CMOS) integrated circuit constructed with N- and P-channel enhancement mode transistors. dual D-type flip-flop is a monolithic complementary MOS (CMOS) integrated circuit constructed with N- and P- channel [ ]. CMOS Dual ‘D’-Type Flip-Flop. Consists of two identical, independent data-type flip-flops. Each flip-flop has independent data, set, reset, and clock inputs and Q.

Author: Zolojinn Aragore
Country: Barbados
Language: English (Spanish)
Genre: Science
Published (Last): 27 February 2013
Pages: 338
PDF File Size: 9.16 Mb
ePub File Size: 7.45 Mb
ISBN: 377-4-20101-551-6
Downloads: 64874
Price: Free* [*Free Regsitration Required]
Uploader: Barisar

The 3 input pins are the data, set, and reset pins. A D flip flop is just a type of flip flop that changes output values according to the input at 3 pins: This is only case when both outputs will be HIGH. D-type flip flops refer to circuits which may have a couple of outputs that change or toggle states in response to triggers applied at the input terminals.

Flips are used in memory devices. B, this will force the Q pin of U1: This clock pin can be obtained from a number of sources such as a frequency generator. The is composed of 2 independent flip flops, labeled on the input as flip flop 1 and flip flop 2. It means it doesn’t matter what logic state the data input is in.

CD – Dual D Flip Flop

Electronic Locks are highly useful to protect our possession and it was widely used in all places. The Pin 1 Q was wired to the Data pin 9 of U1: The 2 output pins are Q and Q. Most of the E-locks in the market are cost more and not i could afford buying these locks.

An dual D flip flop is a pin chip. Set and Reset Inputs Pins 4, 6 and 10, 8: The sets of outputs change states when operated in the bistable mode or while setting and resetting the IC, always producing opposite logic levels at any instant.

  BILDBEARBEITUNG MIT CAPTURE NX2 PDF

If the set pin is 1 and the reset pin is 0 D is Xthen the Q output is 1 and the Q output is 0.

3 Pcs CD4013 4013 IC CMOS Dual D Flip Flop Dip14 Texas

The signal may be applied externally through a transistor astable multivibrator or more conventional types using NAND gates or NOR gates. It can even be obtained from a schmitt trigger inverter chip. This gives a description of each of the pins of the chip. Lc we push down on the pushbutton, this now brings it to a Cs4013 state. Gently adjust and fix the IC on the veroboard somewhere over the center of the board by soldering.

How to Build a D Flip Flop Circuit with a Chip

Pinouts of the IC The D-type blocks consist of four inputs, explained as follows: A is grounded and this in turn gives low output at pin 1 Q when positive edge is encountered in the CLK pin of U1: Frank Donald February 15, 2 Comments. You can physically how the output changes. The IC incorporates two sets of identical, discrete data-type or D-type flip flop modules.

Clock Input Pins 3 and In this circuit, when one LED is on, the other is off. In this circuit, we will operate the flip flop using nothing but manual pushbutton control.

Finally after switch 8 is pressed the Q pin 13 of U2: Below is the truth table for the D flip flop pulled from the datasheet of the chip.

We connect a clock signal to the clock of thewhich is pin 3. For other configurations this input is terminated to any of the logic levels, i. After all the connections are made, have a quick glance and make sure that all have been wired as per the diagram, if possible brush-clean the solder side with thinner. In the above circuit the Switches 1,3,5,8 are wired to feed the clock pulse to each flip flop units U1: You can see mostly for the D or data input.

  DIN 15288 PDF

Therefore, it’s very hands-on and you can really see how a D flip flop operates according to its logic truth table. This state was cd40113 in the whole circuit. A diode was added along with the relay to prevent the reverse flow of current which might damage the IC.

The configurations can be repeated by connecting the modules in series for getting the time period to any desired lengths, but in multiples of two. If the set pin is 0 and the reset pin is 0, while c4013 D pin is 1, then the Q output is 1 and the Q output is 0.

B, this will place the low signal in it. The demand jc Electronic locks is high since it offer high security and easy to handle rather than the mechanical locks. To the Q output pin, we connect a green LED. If the set pin is 1 and the lc pin is 1 D is Xthen the Q output and the Q output are both 1. This means it’s composed of 2 independent flip flops.

If we don’t change the input dc4013, then the values at the outputs stay the same. The diagram illustrates how a IC may be set up for testing its fundamental bistable operation and how it can be further applied for practical uses. Pressing S2 now, just flips the status of the output to its original position.

The astable clocks can be witnessed through LED1. If the set pin is 0 and the reset pin is 1 D is Xthen the Q output is 0 and the Q output is 1.