ASTM A682 PDF

ASTM A Standard Specification for Steel Strip, High Carbon, Cold Rolled, General Requirements. Find the most up-to-date version of ASTM A at Engineering ASTM A, AM – Designation: A /A M – 02 An American National Standard Standard Spe.

Author: Kabar Bamuro
Country: Gabon
Language: English (Spanish)
Genre: Career
Published (Last): 6 October 2013
Pages: 436
PDF File Size: 13.91 Mb
ePub File Size: 2.53 Mb
ISBN: 290-1-95747-759-2
Downloads: 43854
Price: Free* [*Free Regsitration Required]
Uploader: Dojar

C Number 3 edge strip with thickness tolerance a6882 at less than 3? Unless otherwise agreed to, all tests and inspections, except product analysis, shall be made at the place of production.

Dimensions, Mass, and Permissible Variations 9. A number in parentheses indicates the year of last reapproval. Limits on such elements are by agreement between purchaser and supplier. A portion of the coil may be discarded prior to cutting the samples for retest. Note 1—The term weight is used when inch-pound units are the standard.

The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Government procurement by the Defense Supply Agency, strip material shall be continuously marked for identi?

In case of dissatisfaction with the results of the test, the manufacturer may make claims for a rehearing. NOTE 1—Camber is the greatest deviation of a side edge from a straight line, the measurement being taken on the concave side with a straight edge. When agreed by purchaser and supplier, other silicon ranges are permissible. Over 12 Width Tolerance, Plus and Minus, in.

However, under SI the preferred term in mass. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Stay on Page Continue to Compass. Table 3 shows requirements for additional elements.

  EXPORT AWSTATS TO PDF

Strip tolerance products may be available in widths wider than ? This specification covers the general requirements for cold-rolled carbon spring steel strip in coils or cut lengths. C When edge, width and thickness are not de?

Rework and Retreatment When required, minimum coil weights are subject to negotiation. Note 1—The term weight is used when inch-pound units are the standard.

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. The ability of manufacturers to meet the maximum coil weights depends upon individual mill equipment. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.

It is normally produced as a fully killed steel. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

Two additional samples are secured atm each end of the coil from which the original sample was taken. Over 12 Through 11? Combining values from the two systems will result in nonconformance with the specification. The values listed are not exact conversions of the values listed in the inch-pound tables but instead are rounded or rationalized values.

However, unless the order speci? The results of analyses taken from different pieces within a heat may differ from each other and from the ashm analysis. Normal coiling or piling does not provide a 3 Where an ellipsis.

For strip length under mm, x682 tolerance shall be subject to negotiation. Referenced Documents purchase zstm The documents listed below are referenced within the subject standard but a6682 not provided as part of the standard.

  EURPIDES LAS TROYANAS PDF

Conformance to SI tolerances is mandatory when the “M” specification is used. Elements such as aluminum may be added in sufficient amounts to control the austenitic grain size. The values listed are not exact conversions of the values listed in the inch-pound tables but instead are rounded or rationalized values.

The values listed are not exact conversions of the values listed in the inch-pound tables but instead are rounded or rationalized values. B Measured 10 mm or more in from edge; and on narrower than 25 mm, at any place between edges. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.

ASTM A Steel, Strip, High Carbon, Cold Rolled, General Requirements

This standard is subject to revision at any time by the responsible technical committee and must be q682 every? Materials and Manufacture 5. Link to Active This link will aztm route to the current Active version of the standard. Number of Tests and Retests B The sum of copper, nickel, chromium, and molybdenum shall not exceed 0. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM A682 Grade 1074

The material must be adequately protected and correctly identi? Strip is classified as product that is 0. Finish and Edges Link to Active This link will always route to the current Active version of the standard.