ADXL datasheet, ADXL circuit, ADXL data sheet: AD – Low Cost +-2 g/+ g Dual Axis iMEMS Accelerometers with Digital Output,alldatasheet. ADXL 2g Dual Axis Accelerometer With Duty Cycle Outputs FEATURES 2- Axis Acceleration Sensor on a Single IC Chip Measures Static Acceleration as. ADXL Accelerometers are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for ADXL Accelerometers.
|Published (Last):||5 April 2008|
|PDF File Size:||3.30 Mb|
|ePub File Size:||3.1 Mb|
|Price:||Free* [*Free Regsitration Required]|
This pin may be left open circuit or connected to common in normal use. The sensitivity can be determined by the two measurements. When one sensor is reading a maximum change in output per degree, the other is at its minimum.
When this pin is set to VDD, an electrostatic force is exerted on the beam of the accelerometer.
The advantage of this method is an output scale factor of approximately double the analog output. Specific code sets, reference designs, and application notes are available from the factory. This filtering improves measurement resolution and helps prevent aliasing. The actual resolution of the acceleration signal is, however, limited by datashert time resolution of the counting devices used to decode the duty cycle. Therefore, proper ESD precautions are recommended to avoid performance axl202 or loss of functionality.
Its higher sensitivity The equation for the 3 dB bandwidth is: Electrostatic charges as high as V readily accumulate on the human body and test equipment and can discharge without detection.
No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. An op amp follower may be required to buffer this pin. An analog output can be reconstructed by filtering the duty cycle output. Running the part at 3 V will reduce the supply current from 0. This will result in greater dynamic error generated at the DCM.
ADXL Datasheet pdf – ±2 g Dual Axis Accelerometer – Analog Devices
Estimation of Peak-to-Peak Noise When selecting a microcontroller it is helpful to have a counter timer port available. Polysilicon springs suspend the structure over the surface of the wafer and provide a resistance against acceleration forces. A capacitor still must be added at this point for filtering.
However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. However, in some cases, especially where digital devices such as microcontrollers share the same power supply, digital noise on the supply may cause interference on the ADXLE output.
Although the ADXLE features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges.
A proper datashwet will take into account the application requirements for bandwidth, signal resolution and acquisition time, as discussed in the following sections. Table III is useful for estimating the probabilities of exceeding various peak values, given the rms value. The concept is to acquire a reading as quickly as possible and then shut down the ADXLE and the microcontroller until the next sample is needed. It is recommended that the user limit bandwidth to the ratasheet frequency needed by the application, to maximize the resolution and dynamic range of the accelerometer.
An accelerometer uses the force of gravity as an input vector to determine orientation of an object in space. These requirements will help to determine the accelerometer bandwidth, the speed of the microcontroller clock and the length of the T2 period.
In either of the above datassheet, the ADXLE can be turned on and off directly using a digital port pin on the microcontroller to power the datahseet without additional components. The advantage of this method is that the full 5 kHz bandwidth of the accelerometer is available to the user. The outputs are analog voltage or digital signals whose duty cycles ratio of pulsewidth to period are proportional to acceleration.
The ADXLE architecture has been designed so acxl202 these calibrations take place in the software of the microcontroller used to decode the duty cycle signal. Typical Supply Current vs.
ST The ST pin controls the self-test feature. The user must filter the signal at this point to limit aliasing errors.
Typical X-Axis Zero g vs. Decoding algorithms for various microcontrollers have been developed. The accelerometer can measure static acceleration forces such as gravity, allowing it to be used as a tilt sensor. Note that the accelerometer axl202 and sensitivity are ratiometric to the supply voltage.
ADXL Datasheet(PDF) – Analog Devices
Thomas Jefferson, Declaration of Independence. At this point axxl202 pin is available on each channel to allow the user to set the signal bandwidth of the device by adding a capacitor.
Capacitors must be added at these pins to implement low-pass filtering for antialiasing and noise reduction. The following table shows some of the trade-offs.
ADXL202 Data Sheet
Outline of the Declaration of Independence. Power Cycle the xatasheet. It need only be updated to account for changes due to temperature, a relatively slow process. Consult the appropriate Application Note.